Week 14

In this week is the last week for fyp project for all students that we must present on due date. Alhamdulillah, the Final Year Project (FYP) is already over with successfully. First of all, i would like to thank to my supervisor, Sir Izwan Arief Bin Abd Malik with give a lot help, opinions, courage, ideas, encouragement and others for our Final Year Projects. In addition, my partners and i very happy and proud because we are successfully done for the project with my friends from week 1 until week 13. As we know, diploma student will be placed around admin building while degree students will be placed at the Gemilang Hall. The exhibition will be start at 9.00 a.m until 1.00 p.m. Besides that, during presentation for our project we have 2 assessors that will access our fyp project. Lastly, after ends it will announce the winner for the best FYP project and top 20. At below have a picture my partners and i, my friends with very happy smiles...  :)

My partners and i with our project "Water Level Detector"

I'm with my friends after the exhibition ends with happy smiles.

Thanks you my partners, my friend, my supervisor which help us to complete our project with successfully. :)

Week 13

For week 13, we have a final intra briefing which held at TTL 2. So my friend and i plan to go that briefing, the coordinator that be explain about industrial training is Sir Azmi Tajuddin. In explaination its about the final step briefing and give the advice to alert and pay attention about highlight dates, submission dates,submission reply form, letter form and resume. At the same time, he also tell about the last date for find the place for industrial training. So we must make sure that can find the place for intra training due to the date. Besides that, for industrial training that starts in early year 2013, we must register first in the form and we also must know what to do during the industrial training.

In addition, my friend and i plan to design and print the FYP posterwith the size of A1. The poster that we design we used to present in exhibition day at week 14. The FYP poster we put and placed at our booth and in our content in FYP poster we must follow the guideline that given and make a details information such as introduction, abstract, objective, methodology, results, reference, conclusion and others important imformation. Make sure the project is done and understand all the circuit operation and each components that being used.

Week 12

In this week, i'm planning with my partners to make some renovation and modification at my project. We also created a model for our project water level detector to be ready and make sure we can present our project in week 14 which start 8 november 2012 in thursday. The model prototype that we created is simple, when we have a model, it can become easy to present at our assessors. So they can more understand and know about scope of our project.

Week 11

In this week, my partners and i go to the briefing which held at the TTL 1 around 4.30 pm until 5.30pm after excellent award archieve done. At the briefing, the briefing which be conducted by fyp coordinator was explain and tell what we gonna to do around week 14 until week 17. Its also tells about our project fyp can be claim by money which maximum RM300 per student which the claim form must be submitted to advisory by 30 November 2012 with the project with the term and condition which are already set up. At the same time, we must open the RPS Unikl Bmi to tske the FYP Assessment Schemes, FYP Project Submission and others. We also can check our assessors at engineering day around week 14. In addition, we also meet our supervisor to discuss and ask him about our project is functioning or not. We also present to him our new simple circuit that we create to solve the problem which our main circuit have a problem. When the project already trobleshoot the problem, we can focus what we must to do around week 14.

- There is a simple circuit project that we present at my supervisor after troubleshoot the problems.

- We meet our supervisor with a happy smiles..hehe :)

Week 10

In week 10, my partners and i decide to writing the FYP report. Since the due date around week 17, but we want to complete early to make sure that to ensure no delay and complete work assignments in advance. Besides that, we must to planning and research about our report and must take the details information. Its also have a guideline that we must to follow and must to be submitted within the period prescribed by the UniKL bmi. To follow the guide to make sure we are not doing the mistake, we can check and view at website at fyp.bmi.unikl.edu.my.

However, we also doing the troubleshoot problem for our project to make sure our project can functioning or not. In this time, after we solder the component, we check and analyze that it's have a problem at the circuit. In our operation project, "when water bridges the tracks, base current flows and switch on the transistor, sounding the alarm." But our problem is when we connect the battery at the circuit, its sounding and led is lights up before the probes touches the water. So, our solution is to create a new simple circuit which follow the concept project when detect the water, the led will be lights up and sound the alarm.

- This is our main circuit for FYP project that we do which have problem that must be troubleshoot and must detect the problem to solve it.

-There is a simple project that we create to solve our problem that follow the concept for our project. In next week we want to present at my supervisor to discuss and recommend about our FYP project.

Week 9

In week 9, my partners and i was planning to solder the component at the PCB. Before that, we construct the circuit at the breadboard to test and make sure the circuit is functioning or not. So to solder the component, we must assembly the components at the PCB(Printed Circuit Board). Make sure that we assembly the component which must focus at the component place such that we want to put at the PCB such as the value of resistor, capacitor,IC and others. If we put the components in wrong part or places, its will become a big problem that the circuit will not functioning. After assembly the components with a very well at PCB, make sure we solder its with careful and orderly.

-  We put all the component at the PCB board with careful and orderly. After that, we used a black tape to make sure that when we do the process of solder, the component are not drop.

- When the components already in the setup, we ready to solder the component. Make sure that, when solder don't careless because once we solder lead on component make sure it doesn't touch with another leg of component or line of the circuits.

- Once we finish the process of solder, we used cutter to cut the extra leg of the components. Lastly, the process of solder is finish with successfully and functioning.

Week 8

In week 8 ,as we plans before, we discuss and agree to do the process drilling at the uv board. To do this process,we go at 1st floor to use the equipment drill that already give to used. To drill the hole at uv board, its have different drill bit which have small,normal and large. But in my fyp uv board, we just use a small drill bit. The process we doing maybe not take a long time to make it.

The equipment that we used to doing the process are drill machine,and drill bit and spreader.

There is a box equipment that we used to do this process which are "super mini drill 1PK-500".

Inside the box, the component we used are drill machine (which used battery and can be rechargeable), drill   bit and charger.

After that, we drill the hole at uv board which accordance with the polystyrene. Finally, the process drill are succesfully done.